Installation guide for gas fireplaces

commentNo Comments

1. The fireplace should be firmly in place, firmly and perfectly “perpendicular to the ground.
2. Since your fireplace needs fresh and sufficient air for complete combustion, avoid installing it in closed places without separate windows.
3. Do not shake or move the fireplace after it is fully installed.
4. Because the gas fireplace produces toxic gases from the combustion of gas inside the internal body during operation, the chimney pipes must be completely “tight” inside each other.
5. Chimney pipes with a diameter of 10 cm should be used for installation.
6. The length of the gas supply pipe to the fireplace should not be more than 1.5 meters.
7. Make sure that the cap is used on the chimney of the roof of the house.
8. Try to keep the chimney pipes as vertical as possible and avoid installing extra elbows.
9. After the complete installation of the fireplace, check all gas supply connections for gas leakage with soap foam.
10. The fireplace has a spark that manually lights the pilot (candle).

Note: Failure to follow these instructions strictly may result in financial loss, loss of life or death from fire or explosion. Before turning on the heater, smell the surface areas, as some gases are heavier than air and accumulate on the surface.

Note: When installing the fireplace, make sure that the minimum distance around it to the wall is 40 cm.

Whenever you turn on the heater, check that the burner and pilot flame are as shown in the image below. (Special fireplaces equipped with oxygen reduction detection pilot). If the flame is dim, turn off the fireplace and contact the seller or factory after-sales service. Do not confuse orange flames with yellow flames. Dirt or other particles may enter the fireplace and temporarily cause orange flames.

Note:
1. Even though your fireplace glass is safe, do not spray water on it.
2. If the fireplace goes out for any reason, do not turn it on again for at least three minutes. (In the type with pilot equipped with ODS, if the heater is turned off, do not turn it on until fresh air is supplied outside the building).
3. When resting near the fireplace, observe a distance of at least 1 meter.
4. The installation place of the fireplace should be at least 1 meter from the front, top or sides of the heater to flammable objects such as furniture curtains, clothes, etc.
5. Thermostat sensor (fireplaces equipped with thermostatic control valve) is located behind the heater in a place close to the ground. Do not knock, manipulate, apply pressure or move the sensor.

& nbsp;

Criteria for selecting a gas wall-mounted radiator (heating package) for residential units </ b >

& nbsp;

In this article, we want to briefly describe the criteria for selecting a gas wall-mounted radiator for residential homes, and provide a brief description of each of the following to select a wall-mounted radiator. Suitable for residential homes We can provide a little help to all our dear friends and colleagues:

1- Thermal power of wall-mounted radiator

For residential houses without taking into account the area of ​​the residential unit, the minimum required thermal power should be 28 kW. </p >

Devices with lower thermal power, which unfortunately are also widely advertised in the Iranian market, may be suitable at first glance and the ability to provide the required heat to the heating circuit Have residential units with very small area, but when using hot water due to low heat capacity, the device can not meet the needs of both residential units, which include building heating and hot water, so it is recommended. Wall-mounted radiators with a minimum heating power of 28 kW should be used for residential units to maintain the peace and comfort of the occupants of residential houses.

2- Water consumption of wall-mounted radiator

For residential houses without taking into account the building area, the minimum required water consumption should be 13 liters per minute. </ p>

Devices with lower water consumption The residents of residential houses face problems in supplying hot water, some of which include the following: : Low pressure of hot water consumption, permanent and instability of hot water consumption and limitation in using two consumption points for hot water consumption at the same time, so it is recommended to use wall-mounted boilers with a minimum flow rate of 13 liters of hot water Per minute to be used for residential homes to avoid the above-mentioned problems for residents.

3- Wall-mounted radiator fan

It is recommended that the wall-mounted radiator must have a fan, also the fan must be very quiet, so care must be taken in choosing the wall-mounted radiator. And secondly, the device fan is very quiet . (Low noise means less than 40 decibels)

4- Pump wall-mounted radiator

One of the most important things to consider when choosing a wall-mounted radiator is the pump. In reviewing the pump of the device, two points should be considered, one is that the brand of the device pump is a reputable and well-known brand, which is the most famous brand in the field of pump production in the world Named. The next item that should be considered in the review GRUNDFOS can be from the company </ span>

The pump in question is the pump head of the device, which usually most devices in the Iranian market have a circulation pump with a head of 5 meters, but Some devices with 6-meter and 7-meter pump heads are also available in the market, so the higher the pump head of the device, the better, especially in underfloor heating, and in comparison between two wall-mounted radiators similar to the device that pump head It’s more, it’s more appropriate .

5- Wall control valve for wall-mounted radiator

When choosing a wall-mounted radiator, care must be taken that the gas control valve must be modular. Using a modular gas control valve has advantages over a conventional gas control valve. Here are some of them: 1- Controlling the temperature of hot water consumption 2- Less gas consumption 3- Increasing the life of the device, especially the heat exchanger, so be careful when choosing the device that modular gas control valve > Be.

6- Combustion chamber of wall-mounted radiator

Be careful when choosing a wall-mounted radiator for a home where the device must have a closed combustion chamber, close the combustion chamber to prevent the entry of combustion gases The indoor environment is good for the safety of the occupants of the house and also does not use indoor oxygen for combustion.

7- Heat exchanger of wall-mounted radiator

In the market, wall-mounted radiators can be divided into two categories: single-converter wall-mounted radiators and double-converter wall-mounted radiators / p>

Contrary to all the false advertisements about 2-converter wall-mounted radiators, this device was only designed to prevent direct contact of water consumption with the flame. So that when using hot water, the hot water does not become too hot and does not cause a problem for the skin of the consumers, but in addition to this advantage, it also creates disadvantages for the 2 converters, which will not be worth these problems. . One of these problems is the deposition of the secondary converter of the two converters in a very short period of time. Due to the hardness of the water in the area, it is necessary to wash and acid the secondary converter every 4 to 6 months, which requires time and effort. The cost is dear to consumers, while single-converter devices have a biothermal converter that prevents the device from settling due to the special design of the converter, and the converter will not need to be washed or washed for many years. / span>

Another problem that arises in 2-converter devices is the addition of another part called the one-way valve to the set of parts of the device, as well as many breakdowns. Reportedly related to three-way valve. Regardless of the faults related to the three-way valve, one of the problems in the operation of the two converter devices is due to the addition of this valve to the device, closing this valve when using hot water and thus closing the heating circuit path. One of the negative effects is the cooling of the home environment when using the bathroom in the cold season. However, in single-converter devices, there is no one-way switch due to the path

When using hot water, the heating circuit path will not be completely cut off. Bypass < / strong>

Another problem that exists in dual converter devices is the constant operation of the pump when using hot water because it is used to heat hot water. Consumption requires the operation of the pump, which reduces the life of the pump. If in single converter devices, there is no need to operate the pump when using hot water.

8- Simplicity of wall-mounted radiator

Simplicity means that the parts of the device are assembled in such a way that replacing and repairing the parts of the device in case of problems for authorized service personnel is very simple, fast and easy. Be feasible.

9- Spare parts for wall-mounted radiator

When choosing a wall-mounted radiator, care must be taken that the spare parts of that device are provided to customers in abundance and cheaply, so that after the warranty period of the wall-mounted radiator, Cost Do not impose a burden on customers by purchasing spare parts.

10- After-sales service and warranty

Another very important point in choosing any device is to pay attention to after-sales service and its warranty, it is very clear that the longer the warranty period of a device is a sign of the company’s confidence The seller is the quality of the device and therefore the high quality of the device. In addition to warranty, good after-sales service with timely response / prompt action to eliminate the defect of the device / and finally customer satisfaction is also a very important factor in choosing the right device. Is.

مطالب مرتبط

Leave a Reply

Your email address will not be published. Required fields are marked *

Fill out this field
Fill out this field
Please enter a valid email address.
You need to agree with the terms to proceed

Menu